Electric Guitar Repair: 1968 Gibson Melody Maker



 

Luke Crowther from The Rifles dropped by the workshop a few days back. He was collecting his Gibson Melody Maker.

Melody Maker

On the Bench


This lovely old guitar was made in 1968 and has been cherished by Luke for many years until it was worked on by an over enthusiastic guitar tech and was never the same again. After that it didn’t play very well and the intonation was hopelessly wrong.

A possible reason was identified immediately

Wrap Around Tailpiece

The wraparound tail-piece was never a great idea in the first instance and this one was also tipping forward quite acutely. This type of bridge/tailpiece relies on a raised pattern to fix its intonation. Quite a crude idea which only allows for fine adjustment via two small grub screws hidden in the back end of the wraparound. This allows adjustment forwards or backwards ( or  ) and typically never gives enough movement to permit accurate intonation. 

 

Tailpiece Pull up

This has been modified at some point as it still shows the remnants  of the old tremolo system. And removing the scratchplate reveals some crude routing out for the humbuckers. Certainly not factory spec!

Open Cavity

It’s hard to say definitively but it appears that this guitar had a fixed bridge and fixed tremolo as well as single coil pickups. And at some point a previous owner has carried out all these mods.



 

Time to put it right

First thing is to remove the wraparound assembly and trem remnants.

Tailpiece removed

A modern wraparound is bought in to be fitted. This system has separate saddles similar to the Tune O Matic bridges. This will allow the intonation to be set accurately.

New Tailpiece/Adjustable Bridge Assembly

The threaded inserts that are buried into the guitar body are slightly smaller than the originals. Therefore the holes are plugged and re-drilled. To achieve this two Mahogany plugs a turn down on the lathe, inserted and drilled out.

Posthole MeasurementHole Plugs in Lathe12.85mm in Mahogany

With the scratchplate removed a few of the scratchplate screw holes are repaired.

Breakout in cavity

Scratchplate Off Plugs Drilled

With the new wraparound bridge installed and the scratchplate secured correctly the guitar is ready to be set-up.

There is some fret wear which is honed out and the frets re-profiled. The fingerboard is cleaned and oiled and the guitar is re-strung with 10-46 gauge strings.

 


 

Luke checks out the guitars new set-up

Yes he likes it, one very happy Rifleman.

 

Luke Playing a Few Licks

Luke Standing

 

Check out the band on Facebook  https://www.facebook.com/therifles

http://en.wikipedia.org/wiki/The_Rifles_%28band%29

 



 

Bass Guitar Setups London: Sadowsky Bass



I had a visit from Jean-Louis Locas.

Jean-Louis is the bass player with Cirque Du Soleil who are performing their show “Kooza” at the Royal Albert Hall.

Jean-Louis has in his arsenal of instruments a beautiful 5 string bass by Sadowsky. The bass was in need of a quick set-up and a little fret attention mid shows.

Exif_JPEG_PICTURE


Sadowsky are a reputed workshop based in New York who make a fine array of 4 and 5 string basses

More about Shadowsky guitars here


Cirque du Soleil tour with a 5 piece band where the musicians double-up on instruments . It’s made up of bass, guitar, keyboards, drums, percussion and a horn section.

More about Cirque de Soleil here


Catch Jean-Louis in action at the Royal Albert Hall here

Exif_JPEG_PICTURE

Circus of the Sun is in town!

KOOZA | Royal Albert Hall




Acoustic guitar repair London: Gibson 1966 LG-0 (Hot Rod)





Here is an interesting project recently taken in by the workshop: a Gibson LG-O made in 1966

Image  Image

This is an all Mahogany guitar: Mahogany soundboard, back, ribs and neck. This guitar was a budget instrument at the time of manufacture and sold at an affordable price as an entry-level model. The guitar has a slim neck which measures 1 9/16’’ at the nut and joins the body at the 14th fret.

Exif_JPEG_PICTURE

The Bridge

In 1962 with many thousands of the LG-O sold Gibson decided to exchange the standard rectangular Rosewood bridge for a plastic “belly above” type. This plastic moulded version was held in place by 4 screws that attached from under the soundboard up into the base of the bridge. This was done for ease of removal when dealing with replacements. This was upgraded in 1968 with a Rosewood replacement which included an adjustable saddle.

Image  Image

 The Soundboard

The soundboard is ladder-braced with 5 lateral braces across its width. This type of bracing gives a distinctive tone that is indicative of the old acoustic Blues sounds of the 1930s. However, this system lacks structural strength and over time the soundboard can become bulged and distorted with string tension. The over large bridge-plate can exasperate the problem as these where generally made of softwood which also offered little structural strength. The LG-O was discontinued in 1974.



The Brief

Our Brief in this instance was to remove the internal ladder bracing, replace with a scalloped X brace system to give the guitar a more balanced tone and to accentuate the bass tone.

To upgrade the bridge-plate and to make and fit a Rosewood replacement bridge.



Removing the Back

In order to gain easy access to the internal bracing it will be necessary to remove the back.

This LG-O does not have an edge binding around its back outline. Therefore, a thin pallet knife is slipped between the back and the end block to start the separation. Once started a Japanese saw is used to precisely cut through the inner lining. Because of the saw’s thin blade and unique cutting motion very little material is lost during this process.

 

Image Exif_JPEG_PICTURE Image

Once the back is removed the simplistic ladder-brace system is revealed. You will notice that a brace and the bridge-plate are missing. I believe these became loose and subsequently lost years before. Their footprints are still visible.

Image



Rosewood Bridge-Plate

The remaining braces are easily removed and the internal face of the soundboard is prepped in readiness for its upgrade. An Indian Rosewood bridge-plate is made up and fitted. Rosewood is the workshop’s prefered material for bridge-plate replacement because of its strength to thickness ratio.

Exif_JPEG_PICTURE  Exif_JPEG_PICTURE

Go-bars are a very handy and simple way to fit bridge-plates and braces. They are made from flexible timbers that allows pressure to be applied where needed whilst glue is drying.

The Bracing System

The bracing system is made up and glued into place piece by piece.

Each brace is made from 1/4 sawn straight-grained spruce individually scalloped.

Image  Image  Image

Image  Image

 Gluing the Back

Once the bracing system is completed the back is cleaned up and glued into place

Image

A replica of the plastic bridge is made up out of Brazilian Rosewood and fitted

Image

The Set-Up

The frets are showing some wear. They are honed and re-profiled and the truss-rod is adjusted.

The guitar is strung up and tested.

Image  Image

Image

 Conclusion

I’m happy to report that the finished upgrade turned out very well. The guitar has a sweet sound with a good balance. It has a warmth and depth to the bass with sweet mids and trebles. It likes to be picked as well as strummed and I suspect that it will record very nicely and with a small body guitar that’s all you can really ask for.

Full size photos available here on Flickr





Twitter

You can follow Graham Parker Luthier on Twitter  http://twitter.com/gparkerluthier
Any commissions and repairs that I am currently working on can be viewed here with the prefix “On the workbench”.

Follow me and join the debate or just receive an update.

Electric Guitar Repair: Gibson Les Paul Special

Here’s a 10 year old Les Paul Special. It never left the bedroom in all that time and then on its first gig took a tumble when it was hit by a flying mic stand. It was on loan from a careful owner who had never gigged it. Then after just one gig the guitar had a cracked headstock. Ooops!

Click on the image to view the case study.

Les Paul and the Luthier

Graham Parker Luthier discusses the pros and cons of the Gibson Les Paul with the man himself Les Paul at The Iridium Jazz Club, Broadway, NYC. (He makes a few notes)